
How to Design for HDI: Microvia Stacking and Any-Layer
What each BGA pitch band demands in via type, line width and stack-up, from 1.0 mm down to 0.35 mm.
Read article
Multilayer PCBs from 2 to 32 layers — controlled impedance, verified layer registration, and an engineering query back in your inbox within 24 hours.

A multilayer PCB stacks three or more conductive layers separated by dielectric material, laminated into one board with plated interconnections. More layers allow denser routing, better power distribution and cleaner signal return paths — which is why multilayer construction is the default for industrial, medical, AI and communication hardware.
Most factories treat multilayer as a commodity: queue it, run it, ship it. The alternative is engineering it. At HSX CIRCUIT, 80 CAM engineers review 6,000+ unique designs every month, and most multilayer orders return an engineering query within 24 hours — stack-up suggestions, impedance targets, registration risks — before a single panel is imaged.
Every multilayer order runs on automated imaging, drilling and lamination lines, with inner-layer AOI before lamination, coupon-based impedance correlation on every lot, and 100% electrical test before shipment. Prototype and volume builds are reviewed separately, so your production run is planned on its own terms.
Once a panel is laminated, its inner layers can never be inspected or reworked. Inner-layer AOI runs as a hard gate: opens, shorts and dimension issues are caught — and repaired — before they are locked in forever.
Line-width accuracy is impedance accuracy. Compensation ratios are calculated per copper thickness and line class, then verified on first article before the order is released. Minimum trace and space down to 0.075 mm / 0.075 mm.
Ramp rate and pressure profiles are set per prepreg combination to guarantee resin fill and interlayer adhesion. Thick builds (up to 6.0 mm) use staged pressure holds specifically against voids and delamination. Layer-to-layer registration ±50 µm.
Every production panel carries an impedance coupon, measured by TDR. ±5% standard, ±3% on request. Any lot outside tolerance is held for engineering disposition — not shipped.
| Parameter | Capability |
|---|---|
| Layer count | 2–32 layers standard; 50+ on inquiry (sequential lamination) |
| Max panel size | 600 × 900 mm |
| Min trace / space | 0.075 mm / 0.075 mm |
| Board thickness | 0.4–6.0 mm (standard FR-4) |
| Copper weight | 0.5–4 oz inner, 0.5–6 oz outer (heavy copper on inquiry) |
| Impedance control | ±5% standard, ±3% on request; TDR coupon per panel, report ships with CoC |
| Drill | Mechanical from 0.15 mm; aspect ratio 12:1 standard, 20:1 on inquiry |
| Electrical test | 100% — flying probe (prototype), fixture (volume) |
UL 94 V-0 · IPC-6012 / IPC-A-600 · IPC Class 2 standard, Class 3 on request · Full matrix: see Capabilities.
Send your files — a CAM engineer reviews them, not a form.
10-layer mixed-technology control boards, motor drives and PLCs for continuous duty.
8-layer immersion-silver high-speed boards and dense-BGA server boards.
Rigid-flex assemblies for portable diagnostic equipment.
16-layer HDI server boards for accelerator cards.

What each BGA pitch band demands in via type, line width and stack-up, from 1.0 mm down to 0.35 mm.
Read article

Four tolerances, four sensitivities, and why the root-sum-square lands at 7.1% while the worst case reaches 12%.
Read article

Six finishes on flatness, shelf life and cost, and the two questions that remove four of them immediately.
Read article
2 to 32 layers in standard production; higher counts up to 50+ are reviewed per design during engineering query — typically returned within 24 hours.
±5% standard, ±3% on request. Every production panel carries a TDR coupon; measured values ship with the CoC. Out-of-tolerance lots are held for engineering disposition, not shipped.
Gerber (RS-274X) or ODB++ with drill files; stack-up and impedance targets if defined. Upload via our quote page — a CAM engineer, not a form, reviews your files.
No MOQ on fabrication; single-piece prototypes and volume runs are built on the same quality system.
Standard multilayer lead time is confirmed at quotation; rush options are available. We communicate any delay upfront rather than quietly resetting the date.
That’s exactly what we’re built for. Quote in 24 hours.